External Thermal Insulation System
Tile Installation System
Sealing Systems
Repair Construction
Plasters – Renders
Decorative cementitious mortar system
FLEXY 100 C2TES1
Elastic tile adhesive (White) C2TES1
The FLEXY 100 adhesive is used for laying tiles and boards of any type and dimension, such as ceramic or artificial materials, as well as natural building stones, etc., on floors and walls. It is suitable for interior or exterior surfaces. It can be applied on conventional concrete substrates and cementitious renders, on surfaces made of lightweight structural elements (aerated concrete blocks, cement boards and plasterboards, etc.), in areas with relatively high requirements on temperature changes and humidity (heated floors, balconies, bathrooms, etc.). It ensures very good adhesion, high resistance to compression and bending, as well as to changes in temperature and humidity and environmental changes. It prevents visual changes of the surface of white marbles (and other building materials) and the formation of efflorescence. Homogeneous, ready-to-mix, industrial product of consistently high quality. It ensures good workability, increased application speed, it is economical and provides excellent results.
• Mixture of white cement of high specifications and crushed marble of strictly selected granulometry and quality, enriched with polymers and other special improving additives. • It complies with EN12004-1 as a C2TES1 adhesive.
- The substrate must be clean and firm, and it is recommended that it is wetted before application.
- The contents of the bag shall be gradually added to clean water (approximately 4.5-5.0 l/bag) under continuous stirring using an electric mixer at low speed until a homogeneous mixture is obtained. The mixture is left to cure for 5 minutes and then stirred again before the application.
- The adhesive should be applied (“combing”) with a serrated putty knife (6-10 mm). The tiles must be placed and pressed to come to the desired position within 30 minutes. The limits of the application time of the prepared adhesive are such that they allow for any correction needed to fix the tiles in their exact final position.
- If the substrate has been covered with a render, its moisture content should be less than 2.5% before the adhesive is applied.
- During the application of the adhesive, and for a few hours afterwards, extreme climatic conditions (such as strong wind, rain, dust, direct sunlight, etc.) should be avoided and the temperature should be between +5 oC and 35 oC.
- Grouting of floors can be carried out after 24 hours while grouting of walls after 8 hours.
- For even better quality results, see the relevant MARMOPLUS product.
• In bags of 20 kg, pallets and containers of 5 kg. • In a dry place where frost does not form, for 12 months from the date of production, in unopened bags.
2.0-4.0 kg/m2, depending on the type and size of the tiles and the substrate.
Specifications: EN 12004-1
| Granule size | 0.0-0.7 mm |
| Open adhesion time | 30 minutes |
| Apparent dry mortar density | 1300 kg/m3 |
| Adhesion at open adhesion time | ≥1.0 N/mm² |
| Adhesion in dry conditions | ≥1.7 N/mm2 |
| Adhesion when immersed in water | ≥1.1 N/mm2 |
| Adhesion under heating conditions | ≥1.2 N/mm2 |
| Adhesion under freezing-thawing conditions | ≥1.1 N/mm2 |
| Slip | 0.1 mm |
| Grouting on floors | 24 hours |
| Grouting on walls | 8-10 hours |
| Consumption | 2-4 kg/m2 |
| Pot life | 4 hours |
| Micro-adjustments time | 30 minutes |
| Alkali resistance | Excellent |
| Solvent resistance | Excellent |
| Rigidity | ≥2.5 mm |
- The FLEXY 100 adhesive contains cement which is classified as an irritant. Consult the safety instructions and precautions listed in the Material Safety Data Sheet of the product.
- Although the specifications and instructions presented in this bulletin have been prepared to the best of our skills, knowledge and experience, they should be taken as indicative results and require verification after many applications. Users to whom this product is addressed should verify its suitability for the intended application. The end user is responsible for any result of the use of the product.
