External Thermal Insulation System
Tile Installation System
Sealing Systems
Repair Construction
Plasters – Renders
Decorative cementitious mortar system
RG 200 FAST
FAST SETTING TILE ADHESIVE (WHITE) OF CATEGORY: C2FT
The RG 200 FAST adhesive is a fast setting tile adhesive applied where speed of bonding and immediate use of space is required. It is used for laying tiles of any type and dimension, such as ceramic or artificial materials, marble or granite, as well as natural building stones, etc. It is suitable for interior or exterior surfaces on floors and walls. It can be applied on conventional concrete substrates and cementitious renders, on surfaces made of lightweight structural elements (aerated concrete blocks, cement-boards and plasterboards, etc.), in areas with relatively high temperature and humidity requirements (balconies, bathrooms, etc.), in public areas with high daily pedestrian traffic and wherever high construction quality is required. Ready-made product with consistently high quality. It ensures very good adhesion, high resistance to compression and bending, as well as to temperature and humidity changes. Homogeneous, ready-to-mix, industrial product of consistently high quality. It ensures good workability, increased application speed, it is economical and provides excellent results.
Download the TDS - Technical Data Sheet here
Download the DOP - Declaration of Performance here
- Mixture of high specifications white cement and strictly selected granulometry and quality of crushed marble, enriched with polymers and other special improving additives.
- Compliant with EN 12004-1 as C2FT adhesive
.
- The substrate must be clean and firm, and it is recommended that it is wetted before application.
- The contents of the bag shall be gradually added to clean water (approximately 4.5-5.0 l/bag) under continuous stirring using an electric mixer at low speed until a homogeneous mixture is obtained. The mixture is left to cure for 5 minutes and then stirred again before the application.
- The adhesive should be applied (“combing”) with a serrated putty knife (6-10 mm). The tiles must be placed and pressed to come to the desired position.
- The installation of the tiles must take place strictly within the open adhesion time (maximum 20 minutes).
- If the substrate has been covered with any kind of render, its moisture content must be less than 2.5% before the application of the adhesive.
- During the application of the adhesive, and for a few hours afterwards, extreme climatic conditions (such as strong wind, rain, dust, direct sunlight, etc.) should be avoided and the temperature should be between +5 oC and +35 oC.
- Grouting on floors can be done after 3 hours while grouting on walls after 1 hour.
- The RG 200 FAST adhesive should not be used in the following cases. – On big sized marble slabs or other natural stones on bases that are subject to movement. – Directly on plaster walls or plaster mortars, unless an acrylic primer has been applied beforehand. – Directly on metal surfaces, unless they are anti-corrosion protected and an acrylic primer has been applied to them.
- Overdosing with water reduces the expected quality of the product
- For results of even better quality, see the relevant MARMOPLUS product.
- In bags of 20 kg on pallets and containers of 5 kg.
- In a dry place where frost does not form, for 12 months from the date of production, in unopened bags.
2.0-4.0 kg/m2, depending on the type and size of the tiles and the substrate.
Specifications EN 12004-1
| Granule size | 0.0-0.7 mm |
| Open adhesion time | 20 minutes |
| Apparent dry mortar density | 1300 kg/m3 |
| Adhesion at open adhesion time | ≥2.1 N/mm² |
| Adhesion in dry conditions | ≥21N/mm2 |
| Adhesion when immersed in water | ≥1.0 N/mm2 |
| Adhesion under heating conditions | ≥1.4 N/mm2 |
| Adhesion under freezing-thawing conditions | ≥1.1 N/mm2 |
| Slip | ≥0.5 mm |
| Grouting on floors | 1 hour |
| Grouting on walls | 3 hours |
| Consumption | 2-4 kg/m2 |
| Pot life | 1 hour |
| Micro-adjustments time | 10 minutes |
The RG 200 FAST adhesive contains cement which is classified as an irritant. Consult the safety instructions and precautions listed in the Material Safety Data Sheet of the product. Although the specifications and instructions presented in this bulletin have been prepared to the best of our skills, knowledge and experience, they should be taken as indicative results and require verification after many applications. Users to whom this product is addressed should verify its suitability for the intended application. The end user is responsible for any result of the use of the product.
